Diesel Performance Parts

Step 1: Select the Make of your vehicle from the list below.
Step 2: Select your Engine Model.
Step 3: Select the Part Type you’re looking for.
Step 4: Click Find Parts to see all available parts that match your search criteria.

All prices include GST

Bolts Conrod

Part Number: CBTO330A | Status: Available

Conrod bolts to suit CRTO350 (Made in Taiwan)

$5.62 inc. GST

View Part

Camshaft

Part Number: CMTO350 | Status: Available

Camshaft to suit Toyota 1HZ-T and 1HD-T series. (Genuine - made in Japan)

$1,016.40 inc. GST

View Part

Camshaft DPP 8/’95>

Part Number: CMNI130A | Status: Under Development

Camshaft to suit Nissan TD42 series from August 1985 on.

$P.O.A

View Part

Camshaft Performance

Part Number: CMPTO330 | Status: Available

Performance camshaft to suit Toyota 1HZ, 1HZ-T series engines. Suitable for towing or heavy loads. First stage grind for when you fit a turbocharger to a 1HZ – to promote the turbo operation. Later intake valve close, earlier exhaust valve opening and slightly higher lift. The earlier exhaust valve opening lets a bit more of the higher pressure exhaust gases out to get the turbine spinning up sooner and faster.

(New camshaft, performance ground in Australia)

Special note: Due to the amount ground from the base circles of CMPTO330 camshafts, standard shims are not thick enough to set the tappet clearances – it requires approximately 2 mm thicker shims. Sets of test shims are available to calculate thickness of required shims. The shims are a further $180 (shims and freight) on top of the camshaft. Initially as a deposit for the test set and then for the supplied shims.

$781.00 inc. GST

View Part

Camshaft Performance 8/’95>

Part Number: CMPNI130A | Status: Under Development

Performance camshaft to suit Nissan TD42 series from August 1985 on.

$P.O.A

View Part

Camshaft Followers/Buckets

Part Number: CFNI124 | Status: Available

Cam followers to suit Nissan TD42 series. Sold individually. (Paraut brand - made in Japan)

$26.18 inc. GST

View Part

Camshaft Followers/Buckets

Part Number: CFTO330 | Status: Available

Cam buckets to suit Toyota 1HZ, 1HZ-T, 1HD-T series. Sold individually. O.E. Toyota - made in Japan)

$11.55 inc. GST

View Part

Camshaft Follower/Bucket Shims

Part Number: EM37235 to EM37330 | Status: Available

Camshaft Follower/Bucket Shims to suit Toyota 1HZ, 1HZ-T, 1HD-T series. Sizes range between 2.35mm to 3.30mm in 0.05mm increments. Part numbers range between EM37235 and EM37330 in increments of 5 corresponding to the sizes . Sold individually. (Made in Taiwan)

$3.39 inc. GST

View Part

Clutch Kit “Heavy Duty Performance”

Part Number: CKPNI131 | Status: Available

Heavy duty performance clutch kit to suit Nissan TD42 series. Rated to 600Nm of torque. Will suit OE flywheel or performance flywheel - EMPNI131. (from various countries)

$900.90 inc. GST

View Part

Clutch Kit “Extra Heavy Duty Performance”

Part Number: CKPNI131A | Status: Available

Extra heavy duty Performance clutch kit to suit Nissan TD42 series. Rated to 1000Nm of torque. Suits Performance flywheel - EMPNI131. Will not suit OE flywheel. (from various countries)

$P.O.A

View Part

Conrod Performance H-Beam

Part Number: CRFO105A | Status: Available

Set of 5 High performance, H-Beam conrods to suit Ford Ranger, Mazda BT-50 - Oct 2011 onwards, and Everest - Oct 2015 onwards with P5AT/DT32 (5Cyl, 3.2L) engines. Made from billet 40CrMoNiA steel. Conrods are balanced within 2 grams. Fitted with 7/16" 8740 chrome moly bolts (replacements available). Sold as an engine set.

$1,232.00 inc. GST

View Part

Conrod Set

Part Number: CRTO350 | Status: Available

Conrod (aftermarket) to suit Toyota 1HZ-T, 1HD-T/FT/FTE. These conrods are finished on both the big end and small end, however customers may have to very lightly hone the small end to suit their gudgeon pins in some cases.
The conrods are boxed in sets of six by weight - all six conrods in each box are within 2 grams of each other. These conrods have been specifically made for Engine Australia and are an extremely high quality product. (Made in Taiwan)

$1,016.40 inc. GST

View Part

Conrods Forged Billet H-Beam Set

Part Number: CRNI130A | Status: Available

High performance conrod set to suit Nissan TD42T/Ti. Made from forged billet 4340 steel. Conrods are balanced within 1 gram. 30 mm pin. ARP2000 bolts. Sold as an engine set. (Forged in USA, machined in Australia)

$1,971.20 inc. GST

View Part

Conrods Forged Billet H-Beam Set

Part Number: CRTO350B | Status: Available

High performance conrod set to suit Toyota 1HZ-T, 1HD-T series. Made from forged billet 4340 steel. Conrods are balanced within 1 gram. 33 mm pin. ARP2000 bolts. Sold as an engine set. (DPP brand - made in Australia)

$1,980.00 inc. GST

View Part

Crankshaft Damper Hub

Part Number: VDNI130 | Status: Available

Crankshaft damper hub replacement to suit Nissan TD42T/Ti. (Power Bond brand - made in Australia)

$196.75 inc. GST

View Part

Crankshaft Damper Hub Weight Plate

Part Number: VDNI130A | Status: Available

Crankshaft damper weight plate replacement to suit Nissan TD42T/Ti. (Power Bond brand - made in Australia)

$398.86 inc. GST

View Part

Crankshaft Damper Performance

Part Number: VDPNI131A | Status: Available

Performance damper to suit Nissan TD42T/Ti. This unit does not use the taper lock. The crankshaft snout and keyway grooves must be in very good condition. (made in Australia)

$880.00 inc. GST

View Part

Crankshaft Damper – 4 bolt

Part Number: VDTO330A | Status: Available

Crankshaft damper replacement to suit Toyota 1HZ, 1HZ-T, 1HD-T series. 4 bolt auxiliary mount @ 56 mm (O.E. Toyota - made in Japan)

$449.68 inc. GST

View Part

Crankshaft Damper – 6 bolt

Part Number: VDTO330 | Status: Available

Crankshaft damper replacement to suit Toyota 1HZ, 1HZ-T, 1HD-T series. 6 bolt auxiliary mount @ 80 mm (O.E. Toyota - made in Japan)

$252.00 inc. GST

View Part

Crankshaft Damper High Performance Kit

Part Number: VDPNI131 | Status: Available

High performance hub, damper and pulley block to suit Nissan TD42T/Ti Series. The damper is a 7" ATI Super Damper rated at over 1000 H.P. This Damper assembly has been manufactured for performance vehicles that do not require air conditioning drive. The pulley block has two grooves, ONLY for the alternator and power steering. This unit uses the standard taper lock and nut. The crankshaft snout and keyway grooves must be in very good condition.
Note: Not suitable for naturally aspirated TD42 as the hub fouls on the timing case cover
The ATI Super Damper is made in the USA, the Hub and Pulley are made in Australia

$1,848.00 inc. GST

View Part

Get in Touch

Contact our friendly team of experts at Engine Australia today for more information.

Have a question? Call our friendly team of experts today on 1300 ENGINE